XTi2 Series는 Portable PA용으로 디자인되고 만들어진 프로페셔널용 앰프로, 출력파워가 다르다는 것을 제외하고 4모델은 동일한 성능을 갖고 있습니다. XTi 1002, 2002, 4002 그리고 6002 모두 매우 튼튼하면서도 가볍고, 매우 뛰어난 성능을 갖고 있으며, 전면 판낼에 크로스 오버 주파수, EQ, Limiting, Delay 그리고 Subharmonic Synthesizer를 조절할 수 있는 LCD스크린이 있다.
그 밖에도 전세계적으로 통용 가능한 전원 공급스위치모드, 기능성 인디케이터, 냉각을 돕는 스피드 팬, XLR Inputs, Speakon 그리고 Binding Post 출력장치, 누전방지 등 많은 특징들을 갖고 있습니다. 게다가 당신의 XTi2에 대한 투자는 Crown의 3년간의 무과실 손해배상의 보증에 의해 지원됩니다.
XTi1002
XTi2002
XTi4002
XTi6002
2Ω Stereo (per ch.)
700W
1000W
1600W
3000W
4Ω Stereo (per ch.)
500W
800W
1200W
2100W
8Ω Stereo (per ch.)
275W
475W
650W
8Ω Bridge-Mono
2400W
4200W
4Ω Bridge-Mono
1400W
2000W
3200W
6000W
Input EQ
6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.
Crossover Filters
Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control.
Output EQ
8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed.
Delay
For signal alignment of driver; 50 mS of total delay.
SubHarmonic Synth
Takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type.
Peakx™ Plus Limiter
User defeatable limiter that allows users to control Threshold, Attack, and Release times.
Presets
50 total presets, 49 of which are user-definable.
Sensitivity (for full rated power at 4 ohms)
1.4 Vrms
Frequency Response (at 1 watt, 20 Hz - 20 kHz)
+0 dB, –1 dB
Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms)
XTi1002/2002/4002: 100 dB (A weighted)XTi6002: 103 dB (A weighted)
Total Harmonic Distortion (THD)
< 0.5%
Damping Factor 20 Hz to 1 kHz
> 500
Crosstalk (below rated power)
20 kHz - 1 kHz: > 70 db
Input Impedance (nominal)
20k ohms balanced, 10k ohms unbalanced
Maximum Input Signal
+22 dBu typical
AC Line Voltage and Frequency Configurations
100 VAC, 120 VAC, 220-240 VAC 50/60 Hz
AC Line Current (120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch)
XTi1002: 6.8A; no more than 38W at idleXTi2002: 8.3A; no more than 38W at idleXTi4002: 10.5A; no more than 38W at idleXTi6002: 15.3A; no more than 180W at idle
Operating Temperature
0°C to 40°C at 95% relative humidity (non-condensing)
Level
Two front-panel rotary level controls, one for each channel
Power Switch
On/Off switch applies AC power to the amplifier
Sel/Prev/Next Buttons
Three buttons near the LCD screen that are used to access menu items and front panel lockout
LCD Screen
Backlit liquid crystal display that shows preset and processing status
Signal Indicator
Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
–10 Indicator
Green LED flashes when output signal exceeds -10 dB below clip.
–20 Indicator
Green LED flashes when output signal level exceeds -20 dB below clip.
Ready Indicator
Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
Clip Indicator
Red LED, one per channel, turns on at the threshold of audible distortion
Temp Indicator
Red LED, one per channel, illuminates under excessive temperature conditions
Power Indicator
Blue LED illuminates when the amplifier has been turned on and has power
Chassis
Steel
Front Panel
Cast-aluminum
Cooling
Proportional speed fan with front-to-rear airflow.
Dimensions
XTi 1002/2002/4002: 19" (W) x 3.5" (H) x 12.25" (D)XTi 6002: 19" (W) x 3.5" (H) x 16.2" (D)
Net Weight
XTi 1002/2002/4002: 18.5 lbs (8.4kg)XTi 6002: 24.0 lbs (10.9kg)
Shipping Weight
XTi 1002/2002/4002: 21.5 lbs (9.8kg)XTi 6002: 30.0 lbs (13.6kg)
